Albanian language codex of the concept tired.

Albanian language codes:

KAM O (I have O)=strong
N'KAM O/I HAVE NO O=Tired
O symbolizes the complete of a thing. For the energy of the body, it symbolizes maximum power.
When O leaves you, you get tired.
N has two main functions as a code:
1) N as negative
2) N as the direction of movement.
N KAM O=I am not complete, it can be written as a reconstruction of the goals or it can be transormed
NKAMO=
Or:
KAMNO
Where does KAMNO come from? Kamno is the ancient "Greek" word that means fatigue.
While the Albanian word shows the construction code of the word:
LODH (TIRED)=
LOD=DH>D
LOT=D>T
L OT
It means Leave the OT.
Leave the OT's: you get tired
While the root of the Italian stancare (I was tired) is from the Latin STANTIO
STANTIO=
S TANTIO
Negative S and "TAN" of Geg Albanian which means all, whole (i, e) adjective; also as a noun; which is taken whole and undivided; which is in its entirety. The S in the front gives the opposite meaning "not all, not complete, not whole"

While the root of English *tired is the Tēorian word 'fail, come to an end', also 'become physically exhausted' accepted by linguists of unknown origin.
TEORIAN=
TEOLIAN=AN suffix
TE O LI=
Leave O is the code.
Or if we continue the form decomp.sition further in time:
ILOTE=partition of TE with OLI
ILODE=T>D
ILODHE (tired)=D>DH
O LI, O LE is the root of the first word, just like *lodh of the Albanian language "Leave O". D>DH and D>T is an ending form of the Albanian language. Two are the main codic elements of the formation of the thought of the linguistic unit "LODH" the code of L as leave, to go away from, and the universal code of O, the complete of a thing which is metaphorized to the power of the human body
When the O leaves, when it is no longer the O, it is KAMNO, when the O is destroyed, the TEORIAN end comes, the LODH's powers leave.

Comments

Nephilim

N 'eh - Ph 'ih- L 'ee- M / Nepheeleem Zacharia Sitchin (July 11, 1920 – October 9, 2010) wrote the " Nephilim " (נְפִילִים) is derived from “nafàl" and means “fall". The term Nephilim occurs in Genesis 6:1-4, describing the point of time when three things began: men began to increase in number, came into existence the daughters of men , and the sons of God went to the daughters of men and had children by them. Is the "nephillim" really only a Hebrew word? That question is very subtle, however I think it has been more a limit of thinking for linguists rather than a serious argument. Let's begin first with the probable meaning the linguists think it is. We know that the " fall" in every language means moving downward from a higher position involuntarily, usually by an accident, which maybe was the reason why Michael S. Heiser, PhD candidate, Department of Hebrew and Semitic Studies , University of Wisconsin...

Word creation. The "D" letter origin and the "D" pictogram rule of the word creation.

In this article I will cover the origin of the letter D letter, and the pictogram concept of the word creation. It was my first discovery of the word creation. In this blog I will give my discoveries, the rules of word creation of the European languages. Multiple theories exist as to how language first originated. Nobody is sure which one is true. Certified Translations Get Pricing Order Translation What is the Oldest Language in the World? There are over 7,000 languages in the world. Could there have been a time on the earth that we all spoke one language? If so, what is the oldest language in the world? So what was the first language? Discovering the first language that people spoke is difficult because so many languages died and were considered lost in history. However, ancient languages still survive until today; these languages may have been transformed a lot but their old origins may be traceable. Written languages existed but this does n...

Total positional tolerance at material condition

Total positional tolerance at material condition (Hole) Suppose the Ø 1.005 / 1.010 hole is inspected and there are six parts with different ID dimensions. Their actual sizes checked with run out methods give that their actual axis is to be .006” over and up from the true position even though they have different actual ID’s. We want to know which part is within true position tolerance at MMC. Parts to be acceptable require some calculation when is used the run out method. In GD&T, maximum material condition (MMC) refers to a hole that contains the greatest amount of material. To understand and memorize simply and logically the concept, I suppose that you have a part designed as a square with one hole in the center, Ø 1.005 / 1.010 . You have produced just 5 parts and measured their holes. The hole of part #1 is on the low side of its tolerance Ø 1.005" and the hole of part #5 is on high sid...

Linguistic glob

Search This Blog